Anyone had a list of all the materials you can make turbine rotors out of and their efficiencies and such?
I've checked all rotor materials. Only Neutronium is better than TSteel.
Posts by Sapient
-
-
the fusion casings that already exist seem like a good candidate
agreed too
-
Europium in addition to the tungstensteel
Agree
-
[IDEA]
BloodAsp, is it possible to add Ties 2 ProcArray, made from for example Europium and with ability to contain up to 32 (or 64) machines?
-
-
Thanx for answer... but its not good
-
BloodAsp
Is it possible (do you have such plan) to add Amplifab/MassFab support to ProcArray? -
Be+D fuel numbers if anyone's interested.
I have a little different numbers.
216 Recyclers, 12 Amplifabricators, 50 Mass Fabricator, 32 Replicators (or 8 T3), 1 Fluid Extractor, 71 Electrolizer, 94 Centrifuge. Nit Plasma production = 10.94 L/t.
Total consumption 23-27k eU/tNow turbine calculation
Fuel value of plasma = 179 200/10.94 = 16 380 eU/L
Optimal flow = 30 000 / 16 380 = 1.83 (= 2) L/t
Energy production = Optimal flow (2 L/t) * Fuel Value (16 380 eU/L) * Rotor efficiency(140%) = 45 875 eU/tWhile plasma production is 10.94 L/t and one turbine consume only 2 L/t so 5 turbines could be used and total output = 45.8 * 5 - 27 ≈ 200k eU/t
I very hope Recyclers could work within ProcArrays, isn't it Bloody?
-
Also I'm slightly confused about the NEI entry for americium. It says it takes 4 seconds @ 49152 EU/t. That's 3.93 MEU but the total EU listed is 4.71 MEU. Which number is right?
4.71 MEU are right.
Current time = 4.71 MEU / 49152 EU/t ≈ 96t = 4.8 sec. -
Multiply redstone transmitters bug
We have several wireless redstone transmitter covers and only one receiver, all set to same frequency. Receiver detects signal only from last placed transmitter.
I think it should work like OR condition in this case and detects signal from any transmitter.
-
How about advanced, harder to build transformers, that can transformup/down several voltage steps at once?
Nice idea. I need them much too.
-
I later found out that the bee for it does exist, but it simply does not create the Stickyresin comb.
Forestry Unweary Bee produce Stringy Combs. Stringy Combs + Centrifuge = Propolis. Propolis + Centrifuge = Sticky Resin.
-
No, replicators do not work in PA.
Whyyyyyyyyyy?
For uninterrupted production of Beryllium for Be+D reaction its 32 replicators needed. -
Does anyone know will Replicators works in Processing Array? Where should i put data orb?
-
Seems like another bug with Fusion.
1. T1 Fusion with 4 energy hatches can contain only 39 998 488 eU instead of 40 M.
2. After hitting with soft hammer is starts working but didn't consume stored energy. I can stop it after few seconds and start again, Internal buffer stays full. Seems like Fusion Reactor does not consume starting energy at all.GT 5.08.32
-
Why round up? Also in your testing did you find that the rotor numbers also round to the mB/t or is it actually impossible to hit maximum efficiency on most rotors?
Results:
7L/t - 34 067 eU/t
8L/t - 44 223 eU/t
9L/t - 38 818 eU/t
146L/sec - 24 697 eU/t44.2k eU/t is near theoretical maximum of rotor 32*1.4 = 44.8
My test includes rotor spin up (128B of plasma total used), plus some transformer loses (energy collected to 4 slot LuV Bat Buffer), so results are a little lower than it should be. -
I think I read somewhere that the fluid regulator outputs every tick even in second mode and idk how it handles tick rounding.
That was my post and i was wrong.
I made 2 regulators in test creative world and power them with 2 batteries. One of them was set to L/t, another to L/sec. And 1-st one eats 10 eu/t, 2-nd 10 eU/sec (seems like it need 10 eU per operation). -
Also I'm running it at 85 mB/s
As shown my tests, regulator should be set to L/t, not L/sec. Because turbine eats plasma each tick. And value should be rounded to nearest larger integer.
-
Finally after lots of tests and some fails i have my results about best turbine setup for D+T fusion reaction.
Its Large Plasma Turbine with Large TSteel Rotor with fluid regulator set to 8L/t flow and with ZPM Dynamo Hatch.
Total output is 44.2 k eU/t. -
to keep a Be+D reactor fed
Why do you want to make it working constantly?
How much eU can you produce from 2000 of Be Ingots?
Isn't that enough for everything?
