Perfect Breeder, 6 added chambers

  • I am in the process of trying to create a perfect breeder that can "recharge" as many near depleted isotope cells as possible. This is my best attempt to date, I wanted to see if anyone could improve upon what I've done here :)


    http://test.vendaria.net/index…CCHCCCHCCIUCCHCCCHCCCHCCH


    So, it recharges 5 cells using 2 cells, for an overall efficiency of 2.5 I suppose. Curious to see if the efficiency OR the maximum number of cells can be increased while keeping it a perfect breeder. Have at thee my comrades!


    *edit* scratch the efficiency part, I realized how I could easily make my breeder have an efficiency of 4. Too easy of a challenge.

  • I edited one to make it able to increase in heat very slowly. My design heats up extremely slowly, but works. If you replace the Plating with a coolant cell, it starts cooling, but slowly. You could heat it with lava buckets to make it run faster. Or just remove some of the air cooling.
    http://test.vendaria.net/index…CCHCCCHCCIUCCHCCCHCCCHCCH


    Although, nargon made a better breeder. Here's the link of the reconstruction of the breeding mode in the reactor app.
    http://test.vendaria.net/index…CCHCCCHCCIUCCHCCCHCCCHCCH

    Quote

    It has become a little stubbly. Implement facial hair growth in IC²? Vision continuously grows more furry until you shave. (approx once every 2 minecraft days ;P)


    Steve shaves with his chainsaw.
    Check out Factorio- A game where you build a factory from scratch.

  • I edited one to make it able to increase in heat very slowly. My design heats up extremely slowly, but works. If you replace the Plating with a coolant cell, it starts cooling, but slowly. You could heat it with lava buckets to make it run faster. Or just remove some of the air cooling.
    http://test.vendaria.net/index…CCHCCCHCCIUCCHCCCHCCCHCCH

    You write air cooling, but when I look at the schematics, it says water cooling. What should i go for?

    GENERATION 26: The first time you see this, copy it into your sig on any forum and add 1 to the
    generation. Social experiment.

  • Well, My Breeder follows a different approach, ont Uranium cell, recharges up to 8 cells in a single cycle.
    http://test.vendaria.net/index…CXCCCHCCHCCCXCCCHCCHCXCCH


    if you add 4 tiles of water, and block 4 other tiles, it is heat neutral.


    But now to the funny part: heating it up
    1: keep it offline, fill it, add one Uranium cell to the top left corner (as here)
    2: coat ir in Magma
    3: turn it on
    4: around 9.2k hest 2 cells finish with reloading (and thus the heating nearly stops). If you want to get the other 2 cells also recharged, put them in the place of the finished cells, put cooling cells where the unfinished cells were, and replace the magma with the other stuff (as suggested above). It will heat up a bit further, but remains safe. the 2 new coolant cells will melt, if not extracted when hot, but by the time that happens, they did their job.
    5: If you don't want the other cells to recharge, just wait till end of cycle, replace the surroundings, and then use it in regular service


    Testet that way already, and works fine. Once heated up, the cells will recharge at aound half cycle.


    But right now, i'm trying on an automated design to use with BC and red power, if there was something working well, i'll post it.

  • My breeder I made and tested today. I believe it has at least 5 recharges per 2 cells, likely better.
    Mark V EC ( or so it says ) Neutral Breeder


    http://www.talonfiremage.pwp.b…0101401501521s1r11r19</a> 

    [s]
    [/s]

    [s]
    [/s]

    [s]set up completely first before putting lava in.
    can be safely run at 15000 to 16000 heat. (not 9000)
    [/s]

    [s]
    [/s]

    [s]for the base of it I used
    O O O
    O O O O O O= obsidian
    O L C L O L= lava
    O L L L O C= bottom reactor chamber
    O O O
    [/s]

    [s]
    [/s]

    [s]Less plating means less max heat
    DO NOT use any heat distributors, it runs much too hot!
    Meltdown can't happen until at least 16235 heat
    Any wiring you hook up to this will likely melt, this is for dedicated breeding only.
    It will recharge the cell before any components melt.
    Keep away from animals and small children, exposure can kill. 8)



    Never mind. Found out that it maxes out at over 9000. :thumbdown:[/s]