The tooltip for the seismic prospector seems a bit cryptic, how do we "activate with explosives?" (if we're supposed to blow it up, then make that clearer, if not that's what you seem to be implying).
[GregTech-5][1.7.10-FORGE-1355+][Unofficial but approved Port][Stable] Even GT5 Experimental is slowly getting stable.
-
-
Right... "Rightclick with a bunch of TNT" it should be. The amount is not yet fixed and i will be adding other explosives later.
Hm, strange. Pretty sure I tried that. One moment... -
Yeah, regular TNT works, I was in creative so I didn't notice the TNT being used.
-
Quote
The turbine is rounding up to the next integer anyways. So 2mb/t is what it needs. Such low flow rates are really bad anyways because of stuff like this.
Im not sure how to understand this. Will the outputed energy also increase by about 30%? Turbines are allready extremly complicated (e.g. with a nuclear reactor and its fluctuating power output), that makes it even worse. It seems that im forced to use the single block plasma generators, since its impossible to calculate with those large ones...Quotei think, its the problem for all recipes with some chance of output. So, ive got some ore melted, and i have ghost results in my output bus. i think, this problem appears because some of macerators got succeed on some extra dust chance and some macerators are not.
Problem is critical, because slots are taken and nothing in them really. so when, say, 15\16 slots are busy with ghost dusts, we have wasted byproducts, only regular "crushed ore" would appear.
Players can manually drop out ghost dusts, but it works for some really little time, as for my processing, this slot appears busy with ghost dusts within a 5 minutes.
Could you check out output of processing arrays please?upd. Checked array with just one macerator - same problem... so its not bcuz of some macerators have %result and some are not. Wondering, whats the real reason...
So this would also affect the centrifuging of lava? Im currently building a large selfpowered lava centrifgure array (LHE+Steamturbines+40 MV centrifuges) and that would make it impossible to use...
-
What do you mean by "Will the outputed energy also increase by about 30%? "?
-
Sorry to repeat myself, but I CAN use it just without doing anything special, right?
-
Im not sure how to understand this. Will the outputed energy also increase by about 30%? Turbines are allready extremly complicated (e.g. with a nuclear reactor and its fluctuating power output), that makes it even worse. It seems that im forced to use the single block plasma generators, since its impossible to calculate with those large ones...So this would also affect the centrifuging of lava? Im currently building a large selfpowered lava centrifgure array (LHE+Steamturbines+40 MV centrifuges) and that would make it impossible to use...
Im not sure how to understand this. Will the outputed energy also increase by about 30%? Turbines are allready extremly complicated (e.g. with a nuclear reactor and its fluctuating power output), that makes it even worse. It seems that im forced to use the single block plasma generators, since its impossible to calculate with those large ones...So this would also affect the centrifuging of lava? Im currently building a large selfpowered lava centrifgure array (LHE+Steamturbines+40 MV centrifuges) and that would make it impossible to use...
it wont afftect lava, because ghost dusts take slots and when you have result with same dusts, you will get them at those places. Problem is for using many recipes with variety of outputs in array. so when you take all the ghosts slots, new wont appear.
(Sorry if my eng isnt that good, im rus and only learned it from online games and serials) -
Sorry to repeat myself, but I CAN use it just without doing anything special, right?
Да можешь, но если воткнуть жидкостный регулятор, то работать будет эффективнее. Ничего сложного в этом нет.
Я не знаю зачем тому человеку понадобились такие смешные скорости подачи.
Фузионка на дейтерии-тритии производит плазму со скоростью 7,8125л/тик
Оптимальный поток для одной турбины (с большим вольфрамовостальным ротором) - 7,32л/тик (146л/сек)
Разница не велика, но с регулятором на выходе получим 30к eU/t и небольшое количество плазмы будет копиться.
Без регулятора плазма будет уходить вся и выход энергии будети немного меньше (где-то на 6,66%). -
Да можешь, но если воткнуть жидкостный регулятор, то работать будет эффективнее. Ничего сложного в этом нет.
Я не знаю зачем тому человеку понадобились такие смешные скорости подачи.
Фузионка на дейтерии-тритии производит плазму со скоростью 7,8125л/тик
Оптимальный поток для одной турбины (с большим вольфрамовостальным ротором) - 7,32л/тик (146л/сек)
Разница не велика, но с регулятором на выходе получим 30к eU/t и небольшое количество плазмы будет копиться.
Без регулятора плазма будет уходить вся и выход энергии будети немного меньше (где-то на 6,66%).I dont know why u insist on speaking rus everytime I post something. That's offensive, stuff like that goes into pm. Thx nevertheless.
-
Sorry to repeat myself, but I CAN use it just without doing anything special, right?
As i have no idea what you were told in RU: The only issues i know of are certain forge versions in SMP(see first post), ExU after version 1.2.6 and the GT5.09 version that adds its own bees needs the right forestry version.
-
Quote
it wont afftect lava, because ghost dusts take slots and when you have result with same dusts, you will get them at those places. Problem is for using many recipes with variety of outputs in array. so when you take all the ghosts slots, new wont appear.
(Sorry if my eng isnt that good, im rus and only learned it from online games and serials)Great news!
So a workaround for macerators would be getting a realy large output bus? -
Great news!
So a workaround for macerators would be getting a realy large output bus?well, max output bus is 16 slots.. either tungstensteel or neutronium. so.. its too little amount. Or we can use like 1 array for say, 8 or about that different recipes. i said about that, cause output depends on recipe and we can have same phantom dusts, like stone dust.. nickel dust in some ore processing, etc. so when we have common ghost dusts, we can use more recipes to be sure we dont waste output. But i for now have build just parrallede 16 macerators and put all there, waiting for array fix
-
tbh making machine arrays is very gratifying. The only issues the processing array really fixes is loss due to lower voltages (assuming you can feed processing arrays higher voltages and it will do transforming internally) and distributing materials evenly across machines. That last problem can be solved by using the psuedo round robin upgrade with extra utilities pipes (be sure to use the MT script to nerf the hell out of these). I haven't found a better way to do even item distribution than that.
-
https://github.com/Blood-Asp/GT5-Unofficial/issues/200
-
IV Machine Hull:
- Shaped: 2 × 1x Tungsten Cable + 1 × IV Machine Casing
- Assembler: 2 × 2x Tungsten Cable + 1 × IV Machine Casing
-
Max Machine Hull:
- Shaped: 2 × 1x Superconductor Wire + 1 × Max Machine Casing
- Assembler: 2 × 16x Osmium Wire + 1 × Max Machine Casing
-
UV Machine Casing:
- Shaped: 8 × Osmium Plate
- Assembler: NO RECIPE
-
IV Machine Hull:
-
tbh making machine arrays is very gratifying. The only issues the processing array really fixes is loss due to lower voltages (assuming you can feed processing arrays higher voltages and it will do transforming internally) and distributing materials evenly across machines. That last problem can be solved by using the psuedo round robin upgrade with extra utilities pipes (be sure to use the MT script to nerf the hell out of these). I haven't found a better way to do even item distribution than that.
Railcraft Carts with advanced Loaders and Unloaders can distribute items pretty well. You can set which items and how many it will feed each unloader, and those automatically feed the adjacent inventory.
I use one Loader to feed 54 scrap to a cart, and then, this cart distributes 9 scraps each amplifabricator (I have 6). And it's fun to see that cart running through your base =) -
I have upgraded the energy hatch of my EBF to IV.
It receive 4 Amps (8192 EU - 14 EU cable loss) = 8178 EU/ticks from an IV transformer and 14 blocks of 2x Platinum cable (4 amp)Despite this:
Steel ingot recipe 120EU/T * 4 (HV) * 4 (EV) * 4 IV = 7680 EU/t requirement stop after first 2-3 ingots
Tungsten ingot recipe stop after a few seconds.EBF has nichrome coil blocks
worked perfectly in HVThen what are the requirements to have it operate with 8192EU Input?
